Choose a tag by what the equipment is made of and how much wear the spot gets. Fit it where your phone can reach it, then link the tag to its item in the Scannable app.
You can buy all the tags below from the Scannable shop. Still not sure? Try the NFC tag selector.
Which tag for which equipment
| Equipment | Tag | How it fits |
|---|---|---|
| I-beam and H-beam carabiners, other metal devices | Carabiner/hardware tag | Glued with two-part epoxy. Metal only. |
| Round-bar carabiners, 11 to 12mm | Grommet tag | Slides on. No glue. |
| Metal equipment, tools, plastic | Squircle HD on-metal tag | Self-adhesive. |
| Harness labels, small ropes such as prusiks | Under label tag | Self-adhesive. Not for metal. |
| Ropes 5.5mm and thicker, lanyards, cow's tails, cases | NFC rope label | Self-adhesive, under heat shrink. Not for metal. |
| Inside the end of a rope | Rope tag | Pushed into the rope. |
| Plastic helmets | Helmet sticker | Self-adhesive. Not for metal. |
| Harnesses, webbing slings, anchors, Y-lanyards | JOAT (Jack of all Tags) | Fitted with pliers. |
| Anything a zip tie fits round, up to 50mm across | Zip tie tag | Zip tie. |
| Chains and lifting equipment | Dura Tag | Swaged cable, or a screw on a flat surface. |
| Wire rope slings, shackles, webbing slings for heavy lifting | 316 stainless lifting tag | 5mm coated wire cable through its 6mm hole. |
On metal, use a tag made for metal: the carabiner/hardware tag, the Squircle HD, or a lifting tag. Other tags don't read well on metal.
Where to put a tag
- Pick a low-wear spot. Avoid edges, corners, and anywhere that takes knocks or rubbing. On a carabiner, keep the tag away from where the rope runs.
- Keep it reachable. NFC reads only at very close range, so your phone must touch the tag. A carabiner/hardware tag can sit in a recess, but not one so deep that your phone can't reach it.
- Grommet tag: fit it under the gate's locking mechanism, if it doesn't get in the way. Otherwise fit it on the bar.
- Helmet sticker: fit it inside the helmet unless the helmet stays clean. It can often scan through the shell, but check before you rely on that.
- Soft goods: put a backing layer between a Squircle and the webbing.
- Rope labels and under label tags on rope: lay the tag along the rope. Heat shrink makes the rope thicker, so check it still runs through your devices.
Fitting a tag
- Clean the surface with rubbing alcohol or another suitable cleaner. Oil, grease and dirt weaken the bond.
- Fit the tag as the table above describes.
- In high-wear spots, cover the tag (see below).
- Scan the tag to check it reads, then link it to the item.
Gluing carabiner/hardware tags
Carabiner/hardware tags need a two-part epoxy.
- From our shop: JB Weld ClearWeld Epoxy, a 14ml syringe with a mixing nozzle. It sets in 5 minutes and cures in 1 hour. One syringe fits 50 to 75 tags.
- Bought locally: in our tests, Gorilla Epoxy and Selleys Araldite 5 Minute Epoxy gave the best bond. Both set within 3 minutes, dry clear, are waterproof and need no clamping. Loctite Epoxy also works but takes about 15 minutes to set.
Avoid these, which failed our tests:
| Adhesive | Problem |
|---|---|
| Gorilla Super Glue Gel | Made for indoor use only |
| Permabond ET500 | Stays flexible and doesn't stick to the tag's shell |
| White Gorilla Glue | Foams as it sets, so the tag lifts unless clamped |
| Loctite 480 | Very slow to set, and stops some tags reading well |
| Permabond 105 | Can stop some tags reading well, and marks metal |
Fitting a grommet tag
Push the grommet on against a firm edge, such as a wooden bench. If it's stiff, soften it in warm water for a moment first.
Protecting a tag
- Tape: in high-wear spots, put 3M Polyurethane Protective Tape or ISC Leading Edge Tape over the tag. Replace the tape when it wears.
- Heat shrink: cover rope labels, and under label tags on rope, with adhesive-lined heat shrink. Our heat shrink comes in several sizes; 15mm × 30mm fits our rope labels. Shrink it with a heat gun, not a lighter.
Getting a fitted tag to scan
- Hold the tag over your phone's NFC reader. Its position varies by phone. NFC tags won't scan shows how to find it.
- Line up long tags with the phone. Turn carabiner tags, rope tags, JOATs and other rectangular tags so their long side runs along the phone's long edge.
- Face a grommet tag the right way. If your phone's NFC reader is near the top, face the raised part of the grommet inwards. If the reader is in the middle of the back, as on some Android phones, face it outwards.
When to tag your equipment
Pick the approach that suits your team:
- All at once. Add your equipment to Scannable, inspect it and fit tags in one go. Many teams use the switch to Scannable as a fresh start.
- As it comes back. Tag each item when it returns to the store.
To scan a whole folder or kit bag, you can also add NFC to a folder.